Media Broadcaster

Description

a Rasperry Pi-based appliance that streams audio or video via DILC servers. Below is the audio streamer part.

---

Materials

A. Audio Streaming

  * Raspberry Pi (Model B)

  * SD Card with installed Raspbian "Wheezy" OS (Operating System)

         

  * USB Sound Card

  * Audio Computer Microphone

  * USB Micro Cable with Power Brick (5 Volts, 2 Amperes)

  * Ethernet Cable 

  * Fan

    [[File:AC Blower Fan.jpg ] 150 px]

B. For Programming

  *PC Monitor 
  *USB Keyboard
  *USB Mouse
  *VGA to HDMI Cable or RCA Cable

SET-UP

---

Procedure

A. Installing and Running the Rasbian Wheezy OS (Operating System)

  * Use Win32 Disk Imager to write a boot image to your SD Card. 

  * Download the Wheezy zip file and extract the file. 

  * Insert the SD Card into your Raspberry Pi and write the disk image file using the installed win32 Disk Imager. 

B. Setting Static IP

  *Check first the set-up by

        cat /etc/network/interfaces

  then the line iface eth0 inet dhcp implies that the IP address is via DHCP which is dynamically registered by the router. This is what we want to change, if necessary.

  *Get Information

                ifconfig

  with these you will get  the different information that we will use later such as:

  (sample information below)

          inet address (Pi's Current IP Address)= 192.168.0.21 

          Bcast (The Broadcast IP Range)        = 192.168.255.255

           Mask  (Subnet Mask Address)           = 255.255.0.0
  then 

                 netstat -nr or route n 

  (note that these commands will give you the same information)

  Get also the 

  (sample information below)

                   Gateway Address = 192.168.0.231

                   Destination Address = 192.168.0.0 

  *Editing Network Configuration

            open the file /etc/network/interfaces by:

                  sudo nano /etc/network/interfaces

   change the line 

                         iface eth0 inet dhcp
   to
                       iface eth0 inet static

  after this line, directly type the information that we gathered a while ago and save and exit by Ctrl+o and Ctrl+X

   next is to reboot..
                          sudo reboot
  to check:
                           ifconfig

  will reveal the changes or try to ping it with your IP Address by

                  ping (your IP Address) -c 5

C.Programming for the Audio Streaming

  After installing and running the OS of your Raspberry Pi, you are now ready to program the audio streaming.

  Open the LX Terminal,

  *Install PulseAudio and these preference GUI with the command

                 sudo apt-get install pulseaudio

                      sudo apt-get paprefs

                          sudo reboot

  *After the system being rebooted, next thing to do is to edit and add the following lines in the file /etc/pulse/daemon.conf by these command

                  sudo nano /etc/pulse/daemon.conf
  lines: 
        resample-method = ffmpeg

        default-sample-rate = 44100

        alternate-sample-rate = 44100

  after these save and exit by Ctrl+o and Ctrl+x 

  *To make the Raspberry Pi audio server appearing automatically in your "Sound Setting" on every client (PC) and the server (raspberry Pi).

  sudo sed -i 's/AVAHI_DAEMON_DETECT_LOCAL=1/AVAHI_DAEMON_DETECT_LOCAL=0/g' /etc/default/avahi-daemon

  *Activate the network feature of PulseAudio on both client and server.

                           paprefs 

  For the server mark the following boxes

        Network Server -Enable network access to local sound devices

      Network Server -Allow other machines on the LAN to discover local sound devices

         Network Server -Don't require authentication

 For the client you want to stream from the server (Raspberry Pi)

      Network Access -Make discoverable PulseAudio network sound devices available locally

  * Reboot the both server and the client by:

                      sudo reboot 

  After the system reboots, the Sound Setting should appear like these:

  To check if the streaming is working plug in the Computer Audio Microphone in the USB Sound card and start to talk. Note that there will be a delay of 1000ms-2000ms.

D. Connecting the Pulseaudio to the Icecast2 server using the Darkice

  * Compile and Install Darkice
 
                  $ sudo sh -c "echo 'deb-src http://mirrordirector.raspbian.org/raspbian/ wheezy main contrib non-free rpi' >> /etc/apt/sources.list"

                         $ sudo apt-get update

  Install some additional packages

                  sudo apt-get --no-install-recommends install build-essential devscripts autotools-dev fakeroot dpkg-dev debhelper autotools-dev dh-make quilt ccache libsamplerate0-dev libpulse-dev libaudio-dev lame libjack-jackd2-dev libasound-dev libtwolame-dev libfaad-dev libflac-dev libshout3-dev libmp3lame-dev

  Create a working directory

                        $ mkdir src && cd src/

  Get a source package of darkice

                       $ apt-get source darkice

  change the compile configuration to match the Raspbian environment

                            $ cd darkice-1.0/

                           $ vi debian/rules
  change the contents to:

  rules

                   Esc + : + q + ~ to save and exit

  Change the version of the package to reflect mp3 support.

                     $ debchange -v 1.0-999~mp3+1

 Add comments to the changelog like:

              darkice (1.0-999~mp3+1) UNRELEASED; urgency=low

                 * New build with mp3 support

           --  <pi@raspberrypi>  Sat, 11 Aug 2012 13:35:06 +0000

  Now build and intall the darkice package

                  $ dpkg-buildpackage -rfakeroot -uc -b

              $ sudo dpkg -i ../darkice_1.0-999~mp3+1_armhf.deb

  * Configuring DarkIce

                     $ sudo cp darkice.cfg /etc/

  Example of configuration (darkice.cfg)

 # see the darkice.cfg man page for details

# this section describes general aspects of the live streaming session
[general]
duration      = 0                # duration of encoding, in seconds. 0 means    forever
bufferSecs    = 5                # size of internal slip buffer, in seconds
reconnect     = yes              # reconnect to the server(s) if disconnected

# this section describes the audio input that will be streamed
[input]
device        = hw:1,0           # Alsa soundcard device for the audio input
sampleRate    = 44100            # sample rate in Hz. try 11025, 22050 or 44100
bitsPerSample = 16               # bits per sample. try 16
channel       = 1                # channels. 1 = mono, 2 = stereo

# this section describes a streaming connection to an IceCast2 server
# there may be up to 8 of these sections, named [icecast2-0] ... [icecast2-7]
# these can be mixed with [icecast-x] and [shoutcast-x] sections
[icecast2-0]
bitrateMode   = vbr              # variable bit rate
format        = mp3              # format of the stream: mp3
quality       = 0.6              # quality of the stream sent to the server
server        = localhost        # host name of the server
port          = 8000             # port of the IceCast2 server, usually 8000
password      = SOURCE_PASSWORD  # source password to the IceCast2 server
mountPoint    = raspi         # mount point of this stream on the IceCast2     server
name          = RasPi            # name of the stream
description   = DarkIce on RasPi # description of the stream
url           = http://localhost # URL related to the stream
genre         = my genre         # genre of the stream
public        = no               # advertise this stream?
localDumpFile = recording.mp3    # Record also to a file

  Configuration options are explained in the manpage by executing the command:

                           $ man darkice.cfg

  To find the ALSA input devices,

                           $ arecord -l
  It will appear like,

        **** List of CAPTURE Hardware Devices ****
 card 1: U0x46d0x825 [USB Device 0x46d:0x825], device 0: USB Audio [USB Audio]
 Subdevices: 1/1
 Subdevice #0: subdevice #0

  *Installing Icecast2

             $ sudo aptitude install icecast2

  After installing Icecast it will be needed to configure.Set a hostname and passwords for source, relay and administration.The source password will be needed in the darkice.cfg configuration. 

  * Running the DarkIce to Stream audio

                # nice --20 darkice -c /etc/darkice.cfg

To start the streaming automatically, use crontab command:

    open the crontab file by:

                   sudo nano crontab -e

add the line, note that there should be no #'s in front of it

                  @reboot /usr/bin/darkice

save by Ctrl+x, y and enter

when the RPi is rebooted the darkice will automatically start streaming in the shoutcast server. 

Project Team

• Catherine Bagotsay (developer)
• Dawn Benigno (consultant)
• Dan Villareal (consultant)
• Peter Sy (consultant)

---

References

• Raspberry Pi with Raspbian as streaming server via Pulse Audio
• Live mp3 streaming from audio-in with DarkIce and Icecast2 on Raspberry Pi
• Web Streaming With the Raspberry Pi Baby Monitor
• Setting Static IP for the Raspberry Pi
• Automatic streaming audio to the Icecast Server