Difference between revisions of "Media Broadcaster"

Line 123: Line 123:
'''sudo reboot'''
'''sudo reboot'''
to check..
to check..
Line 132: Line 133:
'''ping (your IP Address) -c 5'''
'''ping (your IP Address) -c 5'''
C.Programming for the Audio Streaming
C.Programming for the Audio Streaming

Revision as of 22:18, 15 May 2014


a Rasperry Pi-based appliance that broadcasts video or audio via DILC servers.


A. Audio Streaming

  * Raspberry Pi (Model B)
  * SD Card with installed Raspbian "Wheezy" OS (Operating System)

    Images.jpg     05.png
  * USB Sound Card

  * Audio Computer Microphone
  * USB Micro Cable with Power Brick (5 Volts, 2 Amperes)
    474.jpg     Power brick.jpg
  * Ethernet Cable 

B. For Programming

  *PC Monitor 
  *USB Keyboard
  *USB Mouse
  *VGA to HDMI Cable or RCA Cable


A. Installing and Running the Rasbian Wheezy OS (Operating System)

  • Insert the SD Card into your Raspberry Pi and write the disk image file using the installed win32 Disk Imager.

B. Setting Static IP

  • Check first the set-up by

cat /etc/network/interfaces

then the line iface eth0 inet dhcp implies that the IP address is via DHCP which is dynamically registered by the router.This is what we want to change.

  • Get Information


with these you will get the different information that we will use later such as:

inet address (Pi's Current IP Address)

Bcast (The Broadcast IP Range)

Mask (Subnet Mask Address)


netstat -nr or route n

(note that these commands will give you the same information)

Get also the

Gateway Address

Destination Address

  • Editing Network Configuration

open the file /etc/network/interfaces by:

sudo nano /etc/network/interfaces

change the line

iface eth0 inet dhcp


iface eth0 inet static

then after this line directly type the information that we gathered a while ago then save and exit by Ctrl+o and Ctrl+X

next is to reboot..

sudo reboot

to check..


these will reveal the changes or try to ping it with your IP Address by

ping (your IP Address) -c 5

C.Programming for the Audio Streaming

After installing and running the OS of your Raspberry Pi, you are now ready to program the audio streaming.

Open the LX Terminal,

  • Install PulseAudio and these preference GUI with the command

sudo apt-get install pulseaudio

sudo apt-get paprefs

sudo reboot

  • After the system being rebooted, next thing to do is to edit and add the following lines in the file /etc/pulse/daemon.conf by these command

sudo nano /etc/pulse/daemon.conf


resample-method = ffmpeg

default-sample-rate = 44100

alternate-sample-rate = 44100

after these save and exit by Ctrl+o and Ctrl+x

  • To make the Raspberry Pi audio server appearing automatically in your "Sound Setting" on every client (PC) and the server (raspberry Pi).

sudo sed -i 's/AVAHI_DAEMON_DETECT_LOCAL=1/AVAHI_DAEMON_DETECT_LOCAL=0/g' /etc/default/avahi-daemon

  • Activate the network feature of PulseAudio on both client and server.


For the server mark the following boxes

Network Server -Enable network access to local sound devices

Network Server -Allow other machines on the LAN to discover local sound devices

Network Server -Don't require authentication

For the client you want to stream from the server (Raspberry Pi)

Network Access -Make discoverable PulseAudio network sound devices available locally

  • Reboot the both server and the client by:

sudo reboot

After the system rebooted the Sound Setting should appear like these:

Screenshot from 2013-10-25 10-20-28.png

  • To check if the streaming is working plug in the Computer Audio Microphone in the USB Sound card and start to talk. note that there will be a delay of 1000ms-2000ms.

Project Team

  • Catherine Bagotsay (developer)
  • Dawn Benigno (consultant)
  • Dan Villareal (consultant)
  • Peter Sy (consultant)