User talk:Elijah.lingbanan: Difference between revisions

From Iskomunidad
No edit summary
No edit summary
Line 23: Line 23:


Step I
Step I
   Gather all the components needed and open the remote control carefully. To open the remote, kindly use a drill to open a small hole in the bottom part, else, use the soldering iron to make a hole. Open the remote by pushing through the hole toward the other parts of the remote.
   Gather all the components needed and open the remote control carefully. To open the remote, kindly use a drill to open a small hole in the bottom part, else, use the soldering iron to make a hole. Open the remote by pushing through the hole toward the other parts of the remote.


Step II
Step II
   In the Board of the remote, you will see black prints. This black prints are very thin so do not try to solder in it becase of erased connections due to soldering. Try to sketch the black prints, then connect it with other black prints (the black prints can be said connected by the means of green thin lines connecting them, try to follow the green lines from the black print chosen, and it will lead to other two or three black prints.)
   In the Board of the remote, you will see black prints. This black prints are very thin so do not try to solder in it becase of erased connections due to soldering. Try to sketch the black prints, then connect it with other black prints (the black prints can be said connected by the means of green thin lines connecting them, try to follow the green lines from the black print chosen, and it will lead to other two or three black prints.)


Step III
Step III
   The needed controls here are ON/OFF, UP, DOWN. If you will notice, this buttons are functioning by the means of two close black prints. Those black prints are needed to be controlled, so it must be connected to arduino. There are only five black prints needed, so we will need only five wires to be soldered. We will solder only the green wires attached to the black prints needed (the green wires are insulated. To erase its insulation, kindly use a sharp thing to erase it and be careful). Solder only the bronze part where the insulation is erased. Be careful when soldering the bronze part, for when you pull it too much, the connection of the bronze will be destroyed.
   The needed controls here are ON/OFF, UP, DOWN. If you will notice, this buttons are functioning by the means of two close black prints. Those black prints are needed to be controlled, so it must be connected to arduino. There are only five black prints needed, so we will need only five wires to be soldered. We will solder only the green wires attached to the black prints needed (the green wires are insulated. To erase its insulation, kindly use a sharp thing to erase it and be careful). Solder only the bronze part where the insulation is erased. Be careful when soldering the bronze part, for when you pull it too much, the connection of the bronze will be destroyed.


Step IV
Step IV
   Get the Breadboard and mount up the transistors resistors and wires. The transistor is NPN.  Search for the pin configuration of the transistor (2N3904). The emitter(E) must be connected to the Ground(Gnd), Base(B) connected to the resistor, Collector(C) connected to  the remote control. There are five sets of transistors needed here.
   Get the Breadboard and mount up the transistors resistors and wires. The transistor is NPN.  Search for the pin configuration of the transistor (2N3904). The emitter(E) must be connected to the Ground(Gnd), Base(B) connected to the resistor, Collector(C) connected to  the remote control. There are five sets of transistors needed here.


Step V
Step V
   To connect the collector of each transistor to the remote, kindly pick one of the soldered wires and connect it to the collector of each transistor.
   To connect the collector of each transistor to the remote, kindly pick one of the soldered wires and connect it to the collector of each transistor.


Step VI
Step VI
   To connect the breadboard to the Arduino Micro, connect the Ground of the Breadboard to the ground of the Arduino, the resistors toward the PWMs of arduino. Kindly arrange the connection of the wires frome the remote to the transistor to the resistor to the Arduino.
   To connect the breadboard to the Arduino Micro, connect the Ground of the Breadboard to the ground of the Arduino, the resistors toward the PWMs of arduino. Kindly arrange the connection of the wires frome the remote to the transistor to the resistor to the Arduino.


Step VII
Step VII
   Make the programming of Arduino and codings that is made from the earlier work.
   Make the programming of Arduino and codings that is made from the earlier work.


Step VIII
Step VIII
   If it works, kidly transfer the devices in breadboard to the PCB.
   If it works, kidly transfer the devices in breadboard to the PCB.


Step IX
Step IX
   Scrutinize your work, God Bless!
   Scrutinize your work, God Bless!


Pictures:
Pictures:


/home/Intern/Pictures/Elijah/PCB Board.jpg
 


References:
References:

Revision as of 22:25, 14 April 2014

Web Available Aircon Control

Objective:

 To make a prototype that will make a simple Aircon remote control, controllable by PHP.

Components:

1. 5 pcs. Transistos (2N3904)

2. 5 pcs. Resistors (22K ohms)

3. PCB

4. Breadboard

5. Wires

6. CD-R KING Universal Remote Control

7. Arduino Micro

How to do:

Step I

 Gather all the components needed and open the remote control carefully. To open the remote, kindly use a drill to open a small hole in the bottom part, else, use the soldering iron to make a hole. Open the remote by pushing through the hole toward the other parts of the remote.

Step II

 In the Board of the remote, you will see black prints. This black prints are very thin so do not try to solder in it becase of erased connections due to soldering. Try to sketch the black prints, then connect it with other black prints (the black prints can be said connected by the means of green thin lines connecting them, try to follow the green lines from the black print chosen, and it will lead to other two or three black prints.)

Step III

 The needed controls here are ON/OFF, UP, DOWN. If you will notice, this buttons are functioning by the means of two close black prints. Those black prints are needed to be controlled, so it must be connected to arduino. There are only five black prints needed, so we will need only five wires to be soldered. We will solder only the green wires attached to the black prints needed (the green wires are insulated. To erase its insulation, kindly use a sharp thing to erase it and be careful). Solder only the bronze part where the insulation is erased. Be careful when soldering the bronze part, for when you pull it too much, the connection of the bronze will be destroyed.

Step IV

 Get the Breadboard and mount up the transistors resistors and wires. The transistor is NPN.   Search for the pin configuration of the transistor (2N3904). The emitter(E) must be connected to the Ground(Gnd), Base(B) connected to the resistor, Collector(C) connected to  the remote control. There are five sets of transistors needed here.

Step V

 To connect the collector of each transistor to the remote, kindly pick one of the soldered wires and connect it to the collector of each transistor.

Step VI

 To connect the breadboard to the Arduino Micro, connect the Ground of the Breadboard to the ground of the Arduino, the resistors toward the PWMs of arduino. Kindly arrange the connection of the wires frome the remote to the transistor to the resistor to the Arduino.

Step VII

 Make the programming of Arduino and codings that is made from the earlier work.

Step VIII

 If it works, kidly transfer the devices in breadboard to the PCB.

Step IX

 Scrutinize your work, God Bless!

Pictures:


References:

 "http://arduino.cc/en/Main/arduinoBoardMicro"
 "http://www.instructables.com/id/Control-an-Arduino-with-PHP/?ALLSTEPS"
 "https://www.youtube.com/watch?v=ROBqcQ2YEB8"
 "http://www.instructables.com/id/Build-a-transistor-circuit-board-for-controlling-A/?ALLSTEPS"