Formation and properties of ABA/Polyester Composite - Revision history

Iskwiki.admin at 11:06, 21 April 2012

2012-04-21T11:06:35Z

← Older revision		Revision as of 19:06, 21 April 2012
Line 13:		Line 13:
	[[Category: Materials Science Engineering Thesis]]		[[Category: Materials Science Engineering Thesis]]
	[[Category: College of Engineering Thesis]]		[[Category: College of Engineering Thesis]]
			[[Category:2010 Thesis]]

Mqmallonga at 06:18, 5 February 2012

2012-02-05T06:18:15Z

← Older revision		Revision as of 14:18, 5 February 2012
Line 7:		Line 7:
	The abaca fiber, also known as Manila hemp, that is endemic in the Philippines, was previously shown to have mechanical properties suitable for composite application, where it served as a unidirectional filler or reinforcing material to unsaturated polyester. Considering that in composite preparation, reinforcements in the form of woven fabrics offer a lot of convenience in terms of handling and composite fabrication, it will be beneficial to understand the performance of woven abaca fabric as a reinforcing material to unsaturated polyester. In this study, various configurations of the abaca fiber, i.e. unidirectional or woven, were explored and the mechanical properties of the resulting composites were determined and related to various fabric and composite constructions parameters. All composites were fabricated via vacuum, bagging method and experimentations were divided into two phases; Phase I delved on the variation of the mechanical properties of lamina composites with fiber preparation sequence, and weaving construction; and, Phase 2 delved on mechanical properties of multi-layered composites as a function of inter-lamina distance, lamina configuration, and number of lamina layers. Results of phase 1 showed that composite reinforced with fabric constructed using 20 reed with two ends per dent which underwent chemical treatment after weaving exhibiting the highest tensile strength at 65.155 MPa. Such configuration struck the needed balance between the fiber count and the gap between adjacent yarns, which are the physical manifestations of varying fabric construction in the composite. Furthermore, it was shown that, in a 2-layered composite, higher Young’s modulus was exhibited by samples with low inter-lamina distance and with shifting of fabric layers. The elastic modulus achieved by the composite with this structural configuration is 2.07 GPa. However, in the 4-layered composites, crack formation was observed and is believed to be related to the shrinkage and warpage as suggested by other literatures. Investigation of other weaving patterns, fiber sizing and modification of the matrix system are recommended.		The abaca fiber, also known as Manila hemp, that is endemic in the Philippines, was previously shown to have mechanical properties suitable for composite application, where it served as a unidirectional filler or reinforcing material to unsaturated polyester. Considering that in composite preparation, reinforcements in the form of woven fabrics offer a lot of convenience in terms of handling and composite fabrication, it will be beneficial to understand the performance of woven abaca fabric as a reinforcing material to unsaturated polyester. In this study, various configurations of the abaca fiber, i.e. unidirectional or woven, were explored and the mechanical properties of the resulting composites were determined and related to various fabric and composite constructions parameters. All composites were fabricated via vacuum, bagging method and experimentations were divided into two phases; Phase I delved on the variation of the mechanical properties of lamina composites with fiber preparation sequence, and weaving construction; and, Phase 2 delved on mechanical properties of multi-layered composites as a function of inter-lamina distance, lamina configuration, and number of lamina layers. Results of phase 1 showed that composite reinforced with fabric constructed using 20 reed with two ends per dent which underwent chemical treatment after weaving exhibiting the highest tensile strength at 65.155 MPa. Such configuration struck the needed balance between the fiber count and the gap between adjacent yarns, which are the physical manifestations of varying fabric construction in the composite. Furthermore, it was shown that, in a 2-layered composite, higher Young’s modulus was exhibited by samples with low inter-lamina distance and with shifting of fabric layers. The elastic modulus achieved by the composite with this structural configuration is 2.07 GPa. However, in the 4-layered composites, crack formation was observed and is believed to be related to the shrinkage and warpage as suggested by other literatures. Investigation of other weaving patterns, fiber sizing and modification of the matrix system are recommended.

			Subject Index : Polyester Fibers

Mhmisolas: FORMATION AND PROPERTIES OF ABA/POLYESTER COMPOSITE moved to Formation and properties of ABA/Polyester Composite

2011-09-07T06:46:02Z

Formation and properties of ABA/Polyester Composite moved to Formation and properties of ABA/Polyester Composite

← Older revision		Revision as of 14:46, 7 September 2011
(No difference)

Mhmisolas: New page: '''Lady Marianne E. Polinga''' (MS Graduated: 1st Sem 2009-2010) '''Abstract''' The abaca fiber, also known as Manila hemp, that is endemic in the Philippines, was previously shown to ...

2011-09-07T06:45:26Z

New page: '''Lady Marianne E. Polinga''' (MS Graduated: 1st Sem 2009-2010) '''Abstract''' The abaca fiber, also known as Manila hemp, that is endemic in the Philippines, was previously shown to ...

New page

'''Lady Marianne E. Polinga'''

(MS Graduated: 1st Sem 2009-2010)

'''Abstract'''

The abaca fiber, also known as Manila hemp, that is endemic in the Philippines, was previously shown to have mechanical properties suitable for composite application, where it served as a unidirectional filler or reinforcing material to unsaturated polyester. Considering that in composite preparation, reinforcements in the form of woven fabrics offer a lot of convenience in terms of handling and composite fabrication, it will be beneficial to understand the performance of woven abaca fabric as a reinforcing material to unsaturated polyester. In this study, various configurations of the abaca fiber, i.e. unidirectional or woven, were explored and the mechanical properties of the resulting composites were determined and related to various fabric and composite constructions parameters. All composites were fabricated via vacuum, bagging method and experimentations were divided into two phases; Phase I delved on the variation of the mechanical properties of lamina composites with fiber preparation sequence, and weaving construction; and, Phase 2 delved on mechanical properties of multi-layered composites as a function of inter-lamina distance, lamina configuration, and number of lamina layers. Results of phase 1 showed that composite reinforced with fabric constructed using 20 reed with two ends per dent which underwent chemical treatment after weaving exhibiting the highest tensile strength at 65.155 MPa. Such configuration struck the needed balance between the fiber count and the gap between adjacent yarns, which are the physical manifestations of varying fabric construction in the composite. Furthermore, it was shown that, in a 2-layered composite, higher Young’s modulus was exhibited by samples with low inter-lamina distance and with shifting of fabric layers. The elastic modulus achieved by the composite with this structural configuration is 2.07 GPa. However, in the 4-layered composites, crack formation was observed and is believed to be related to the shrinkage and warpage as suggested by other literatures. Investigation of other weaving patterns, fiber sizing and modification of the matrix system are recommended.

[[Category: Theses]]
[[Category: Materials Science Engineering Thesis]]
[[Category: College of Engineering Thesis]]